C67300 Bronzo al manganese
SAE J461, SAE J463
This is a high strength leaded silicon manganese bronze with typically good bearing qualities. This alloy maintains high impact resistance with excellent machinability making it well suited for clutch bearings, shaft bushings, sleeve bearings, thrust bearings, pump parts, drive shafts, bearing pins, wear plates, gears and cams. Resists squashing out under high loads and extreme wear applications.
Typical Uses for C67300 Manganese Bronze:
Applicazioni tipiche
FISSAGGI: Fasteners, Lead Screw Nuts
INDUSTRIALE: Gears and Cams, Wear Plates, Bushings, Seal Rings, Idler Pins, Piston Heads, Brearing Pins, Thrust Bearings, Sleeve Bearings, Propeller Shafts, Shaft Bushings, Clutch Bearings, Drive Shafts, Spindles, Pump Parts, Bearings
MARINO: Hardware, Valve Seats
OTHER: Connecting Rods
C67300 Typical uses
Tough and corrosion resistant, C67300 manganese bronze, also known as C673, is a high-tensile bronze ideal for high-load, low-speed applications that require a combination of outstanding wear characteristics and high bearing strength.
Fasteners: fasteners, lead screw nuts
Industrial: bearings, bearings (pins) bushings, clutch bearings, drive shafts, gears and cams, idler pins, piston heads, propeller shafts, pump parts, seal rings, shaft bushings, sleeve bearings, spindles, thrust bearings, wear plates
Marine: hardware, valve seats
Other: connecting rods
Specifica simile o equivalente
CDA | ASMA | SAE | AMS | Federale | Militare | Altro |
---|---|---|---|---|---|---|
C67300 | J461 J463 |
Composizione chimica
Cu% | Pb% | Sn% | Zn% | Fe% | In 1 | Al% | Mn% | E% | |||
---|---|---|---|---|---|---|---|---|---|---|---|
Chemical composition according to SAE J463 Il valore 1Ni include Co. Note: Single values represent maximums. | |||||||||||
58.00- 63.00 | 0.40- 3.00 | 0.30 | REM. | 0.50 | 0.25 | 0.25 | 2:00- 3.50 | 0.50- 1,50 |
lavorabilità
Lega di rame N. UNS | Grado di lavorabilità | Densità (lb/in3 a 68 °F) |
---|---|---|
C67300 | 70 | 0.300 |
Proprietà meccaniche
C67300
H02 semiduro
Size range: up to 1″ inclusive
Resistenza alla trazione, min | Carico di snervamento, allo 0,5% di estensione sotto carico, min | Allungamento, in diametro 4x o spessore del provino, min | Durezza Rockwell “B”. | la lega ha il doppio della sua resistenza alla compressione | ||
---|---|---|---|---|---|---|
ksi | MPa | ksi | MPa | % | min HRB | |
65 | 448 | 40 | 276 | 12 | 70 |
Size range: over 1″ to 3″ inclusive
Resistenza alla trazione, min | Carico di snervamento, allo 0,5% di estensione sotto carico, min | Allungamento, in diametro 4x o spessore del provino, min | Durezza Rockwell “B”. | la lega ha il doppio della sua resistenza alla compressione | ||
---|---|---|---|---|---|---|
ksi | MPa | ksi | MPa | % | min HRB | |
58 | 400 | 35 | 241 | 15 | 70 |
Size range: over 3″
Resistenza alla trazione, min | Carico di snervamento, allo 0,5% di estensione sotto carico, min | Allungamento, in diametro 4x o spessore del provino, min | Durezza Rockwell “B”. | la lega ha il doppio della sua resistenza alla compressione | ||
---|---|---|---|---|---|---|
ksi | MPa | ksi | MPa | % | min HRB | |
55 | 380 | 30 | 205 | 18 | 65 |
Proprietà fisiche
Proprietà fisiche fornite da CDA | |||||||||||
Consuetudine statunitense | Metrica | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Punto di fusione – liquido | 1605 °F | 874 °C | |||||||||
Densità | 0.3 lb/in3 at 68 °F | 8.3 gm/cm3 at 20 °C | |||||||||
Peso specifico | 8.3 | 8.3 | |||||||||
Conduttività elettrica | 22% IACS at 68 °F | 0.13 MegaSiemens/cm at 20 °C | |||||||||
Conduttività termica | 55 Btu/sq ft/ft hr/°F at 68 °F | 95 W/m at 20 °C | |||||||||
Coefficiente di dilatazione termica 68-572 | 11 · 10-6 per °F (68-572 °F) | 19 · 10-6 per °C (20-300 °C) | |||||||||
Modulo di elasticità a trazione | 17000 ksi | 117212MPa |
Proprietà di fabbricazione
Proprietà di fabbricazione fornite da CDA | |||||||||||
Tecnica | adeguatezza | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Grado di lavorabilità | 70 |
Processi di fabbricazione comuni
Hot forging and pressing, machining
Processi di fabbricazione comuni forniti da CDA